SSD1963 Display Controller Command List. More...

Macros
#define	SSD1963_CMD_NOP 0X00
	No operation.

#define	SSD1963_CMD_SOFT_RESET 0x01
	Software Reset.

#define	SSD1963_CMD_GET_POWER_MODE 0x0A
	Get the current power mode.

#define	SSD1963_CMD_GET_ADDRESS_MODE 0x0B
	Get the frame buffer to the display panel read order.

#define	SSD1963_CMD_GET_DISPLAY_MODE 0x0D
	The SSD1963 returns the Display Image Mode.

#define	SSD1963_CMD_GET_TEAR_EFFECT_status 0x0E
	Get the Tear Effect status.

#define	SSD1963_CMD_ENTER_SLEEP_MODE 0x10
	Turn off the panel. This command will pull high the GPIO0. If GPIO0 is configured as normal GPIO or LCD miscellaneous signal with command set_gpio_conf, this command will be ignored.

#define	SSD1963_CMD_EXIT_SLEEP_MODE 0x11
	Turn on the panel. This command will pull low the GPIO0. If GPIO0 is configured as normal GPIO or LCD miscellaneous signal with command set_gpio_conf, this command will be ignored.

#define	SSD1963_CMD_ENTER_PARTIAL_MODE 0x12
	Part of the display area is used for image display.

#define	SSD1963_CMD_ENTER_NORMAL_MODE 0x13
	The whole display area is used for image display.

#define	SSD1963_CMD_EXIT_INVERT_MODE 0x20
	Displayed image colors are not inverted.

#define	SSD1963_CMD_ENTER_INVERT_MODE 0x21
	Displayed image colors are inverted.

#define	SSD1963_CMD_SET_GAMMA_CURVE 0x26
	Selects the gamma curve used by the display panel.

#define	SSD1963_CMD_SET_DISPLAY_OFF 0x28
	Blanks the display panel.

#define	SSD1963_CMD_SET_DISPLAY_ON 0x29
	Show the image on the display panel.

#define	SSD1963_CMD_SET_COLUMN_ADDRESS 0x2A
	Set the column address.

#define	SSD1963_CMD_SET_PAGE_ADDRESS 0x2B
	Set the page address.

#define	SSD1963_CMD_WRITE_MEMORY_START 0x2C
	Transfer image information from the host processor interface to the SSD1963 starting at the location provided by set_column_address and set_page_address.

#define	SSD1963_CMD_READ_MEMORY_START 0x2E
	Transfer image data from the SSD1963 to the host processor interface starting at the location provided by set_column_address and set_page_address.

#define	SSD1963_CMD_SET_PARTIAL_AREA 0x30
	Defines the partial display area on the display panel.

#define	SSD1963_CMD_SET_SCROLL_AREA 0x33
	Defines the vertical scrolling and fixed area on display area.

#define	SSD1963_CMD_SET_TEAR_OFF 0x34
	Synchronization information is not sent from the SSD1963 to the host processor.

#define	SSD1963_CMD_SET_TEAR_ON 0x35
	Synchronization information is sent from the SSD1963 to the host processor at the start of VFP.

#define	SSD1963_CMD_SET_ADDRESS_MODE 0x36
	Set the read order from frame buffer to the display panel.

#define	SSD1963_CMD_SET_SCROLL_START 0x37
	Defines the vertical scrolling starting point.

#define	SSD1963_CMD_EXIT_IDLE_MODE 0x38
	Full color depth is used for the display panel.

#define	SSD1963_CMD_ENTER_IDLE_MODE 0x39
	Reduce color depth is used on the display panel.

#define	SSD1963_CMD_WRITE_MEMORY_CONTINUE 0x3C
	Transfer image information from the host processor interface to the SSD1963 from the last written location.

#define	SSD1963_CMD_READ_MEMORY_CONTINUE 0x3E
	Read image data from the SSD1963 continuing after the last read_memory_continue or read_memory_start.

#define	SSD1963_CMD_SET_TEAR_SCANLINE 0x44
	Synchronization information is sent from the SSD1963 to the host processor when the display panel refresh reaches the provided scan line.

#define	SSD1963_CMD_GET_SCANLINE 0x45
	Get the current scan line.

#define	SSD1963_CMD_READ_DDB 0xA1
	Read the DDB from the provided location.

#define	SSD1963_CMD_SET_LCD_MODE 0xB0
	Set the LCD panel mode and resolution.

#define	SSD1963_CMD_GET_LCD_MODE 0xB1
	Get the current LCD panel mode, pad strength and resolution.

#define	SSD1963_CMD_SET_HORI_PERIOD 0xB4
	Set front porch.

#define	SSD1963_CMD_GET_HORI_PERIOD 0xB5
	Get current front porch settings.

#define	SSD1963_CMD_SET_VERT_PERIOD 0xB6
	Set the vertical blanking interval between last scan line and next LFRAME pulse.

#define	SSD1963_CMD_GET_VERT_PERIOD 0xB7
	Get the vertical blanking interval between last scan line and next LFRAME pulse.

#define	SSD1963_CMD_SET_GPIO_CONF 0xB8
	Set the GPIO configuration. If the GPIO is not used for LCD, set the direction. Otherwise, they are toggled with LCD signals.

#define	SSD1963_CMD_GET_GPIO_CONF 0xB9
	Get the current GPIO configuration.

#define	SSD1963_CMD_SET_GPIO_VALUE 0xBA
	Set GPIO value for GPIO configured as output.

#define	SSD1963_CMD_GET_GPIO_STATUS 0xBB
	Read current GPIO status. If the individual GPIO was configured as input, the value is the status of the corresponding pin. Otherwise, it is the programmed value.

#define	SSD1963_CMD_SET_POST_PROC 0xBC
	Set the image post processor.

#define	SSD1963_CMD_GET_POST_PROC 0xBD
	Get the image post processor.

#define	SSD1963_CMD_SET_PWM_CONF 0xBE
	Set the image post processor.

#define	SSD1963_CMD_GET_PWM_CONF 0xBF
	Get the image post processor.

#define	SSD1963_CMD_SET_LCD_GEN0 0xC0
	Set the rise, fall, period and toggling properties of LCD signal generator 0.

#define	SSD1963_CMD_GET_LCD_GEN0 0xC1
	Get the current settings of LCD signal generator 0.

#define	SSD1963_CMD_SET_LCD_GEN1 0xC2
	Set the rise, fall, period and toggling properties of LCD signal generator 1.

#define	SSD1963_CMD_GET_LCD_GEN1 0xC3
	Get the current settings of LCD signal generator 1.

#define	SSD1963_CMD_SET_LCD_GEN2 0xC4
	Set the rise, fall, period and toggling properties of LCD signal generator 2.

#define	SSD1963_CMD_GET_LCD_GEN2 0xC5
	Get the current settings of LCD signal generator 2.

#define	SSD1963_CMD_SET_LCD_GEN3 0xC6
	Set the rise, fall, period and toggling properties of LCD signal generator 3.

#define	SSD1963_CMD_GET_LCD_GEN3 0xC7
	Get the current settings of LCD signal generator 3.

#define	SSD1963_CMD_SET_GPIO0_ROP 0xC8
	Set the GPIO0 with respect to the LCD signal generators using ROP operation. No effect if the GPIO0 is configured as general GPIO.

#define	SSD1963_CMD_GET_GPIO0_ROP 0xC9
	Get the GPIO0 properties with respect to the LCD signal generators.

#define	SSD1963_CMD_SET_GPIO1_ROP 0xCA
	Set the GPIO1 with respect to the LCD signal generators using ROP operation. No effect if the GPIO1 is configured as general GPIO.

#define	SSD1963_CMD_GET_GPIO1_ROP 0xCB
	Get the GPIO1 properties with respect to the LCD signal generators.

#define	SSD1963_CMD_SET_GPIO2_ROP 0xCC
	Set the GPIO2 with respect to the LCD signal generators using ROP operation. No effect if the GPIO2 is configured as general GPIO.

#define	SSD1963_CMD_GET_GPIO2_ROP 0xCD
	Get the GPIO2 properties with respect to the LCD signal generators.

#define	SSD1963_CMD_SET_GPIO3_ROP 0xCE
	Set the GPIO3 with respect to the LCD signal generators using ROP operation. No effect if the GPIO3 is configured as general GPIO.

#define	SSD1963_CMD_GET_GPIO3_ROP 0xCF
	Get the GPIO3 properties with respect to the LCD signal generators.

#define	SSD1963_CMD_SET_DBC_CONF 0xD0
	Set the dynamic back light configuration.

#define	SSD1963_CMD_GET_DBC_CONF 0xD
	Get the current dynamic back light configuration.

#define	SSD1963_CMD_SET_DBC_TH 0xD4
	Set the threshold for each level of power saving.

#define	SSD1963_CMD_GET_DBC_TH 0xD5
	Get the threshold for each level of power saving.

#define	SSD1963_CMD_SET_PLL 0xE0
	Start the PLL. Before the start, the system was operated with the crystal oscillator or clock input.

#define	SSD1963_CMD_SET_PLL_MN 0xE2
	Set the PLL.

#define	SSD1963_CMD_GET_PLL_MN 0xE3
	Get the PLL settings.

#define	SSD1963_CMD_GET_PLL_STATUS 0xE4
	Get the current PLL status.

#define	SSD1963_CMD_SET_DEEP_SLEEP 0xE5
	Set deep sleep mode.

#define	SSD1963_CMD_SET_LSHIFT_FREQ 0xE6
	Set the LSHIFT (pixel clock) frequency.

#define	SSD1963_CMD_GET_LSHIFT_FREQ 0xE7
	Get current LSHIFT (pixel clock) frequency setting.

#define	SSD1963_CMD_SET_PIXEL_DATA_INTERFACE 0xF0
	Set the pixel data format of the parallel host processor interface.

#define	SSD1963_CMD_GET_PIXEL_DATA_INTERFACE 0xF1
	Get the current pixel data format settings.

Macros

Detailed Description